Phoenix RepRap: Difference between revisions
No edit summary |
|||
Line 109: | Line 109: | ||
|Extruder parts pcb strip board, Kapton tape, 6-ohm length of fibreglass-insulated nichrome wire,heatshrink tubing, silicon grease | |Extruder parts pcb strip board, Kapton tape, 6-ohm length of fibreglass-insulated nichrome wire,heatshrink tubing, silicon grease | ||
|? | |? | ||
| | |Grainger, Frys,? | ||
|- | |- | ||
|Misc - oil, box cutter blades, more? | |Misc - oil, box cutter blades, more? |
Revision as of 21:45, 11 January 2010
Project Synopsis
We've been trying to brainstorm a good project idea that we can focus on to present to ASU for the $2000 grant we're aiming for. One project that would definitely put us on the map and would also allow us to reach out to the local community would be procuring a Rapid-Prototyping device. The RepRap project is a prime example of one whose initial creator's intention was not only to make a device that was as inexpensive as possible but also one that can replicate itself. Seeing the cost benefits analysis, as well as, the vast improvements with version II of this device(Mendel) we're thinking about going with that design.
Design Summary
Check out the RepRap main site here:
http://reprap.org/bin/view/Main/WebHome
They've got a great video/mini documentary explaining the background of the RepRap concept including an interview with the designer:
http://vimeo.com/5202148
Check out the below link for a good video summary of what the "Mendel" is:
http://objects.reprap.org/wiki/Mendel_Overview
Construction
The RepRap team has done a pretty good job of ensuring that the design specs are open source so that the world wide community can participate in building and even bettering what they've started.
Below is their how to section on building a "Mendel" version of the RepRap:
http://objects.reprap.org/wiki/How_to_make_RepRap_Version_II_%22Mendel%22
Budget
This is a tally of costs so far, and providers used. You can see the original estimate on the rep rap site of $520 was rather low. With all the various shipping charges (plus we got 15lbs of plastic) we will likely almost double this. They also do not mention the impossibility of finding the prototyped/printed parts for the rep rap. They are approximately 100 hours to print and thus we've found few rep rap/makerbot owners willing or able to print those parts for us. These parts can also be rapid prototyped for around $1500 dollars which is slightly more than the advertised $20 dollars.
Located Parts
Item | US cost | Notes |
Bearings | $76.14 shipped | TheBigBearingStore.com |
Fasteners | 109.20 | Mcmaster.com |
Belt | see Fasteners | Mcmaster.com |
Extruder parts(machined) | $32.40 shipped | reifsnyderb on rep rap forums |
Motors | 302.85 shipped | Store.Makerbot.com |
Plastic Stock | See motors | Store.Makerbot.com |
PCBs | See Motors | Makerbot |
Electronics | 169.16 | Parted out from Digikey, Allied,Arrow,Newark and Mouser |
Thick sheet MDF, between 4mm and 6mm and at least 42cmx40cm | 57.15 | Lowes |
Bar (smooth rod) BZP NOT BMS A2 Steel even better - at least 3m - M8 (8mm diameter) | See Thick Sheet | Lowes |
Studding (threaded rod) -BZP M8 (8mm diameter) at least 9 meters | See Thick Sheet | Lowes |
epoxy,ties | See Thick Sheet | Lowes |
Total | £689.74 | ' |
NEEDED PARTS
These are the parts we still need. Perhaps you can help?
Item | US cost | Notes |
12 PC or laptop Power Supply | ? | Scrap - You? |
Thin sheet less than 2mm thick and at least 8cmx5cm | ? | Beer can? |
Printed Parts | ? | Laser Cut, Rapid Prototyped, or Printed? |
Extruder parts pcb strip board, Kapton tape, 6-ohm length of fibreglass-insulated nichrome wire,heatshrink tubing, silicon grease | ? | Grainger, Frys,? |
Misc - oil, box cutter blades, more? | ? | Lowes, Home Depot |
Total | ? | ' |
Build Plan
Sorting parts into 'kits' (whole lotta parts to sort) Soldering - 2 or 3 stations probably (12 boards of various complexity) Testing Extruder building - going to be dependent on us getting prototyped parts in time Mechanical construction - going to be dependent on us getting prototyped parts in time