PCB Etching: Difference between revisions

From HeatSync Labs Wiki
Jump to navigation Jump to search
VisualWikitext
en>Meznak
en>Meznak
No edit summary
Line 17: Line 17:
some good but perhaps outdated info from ladyada
some good but perhaps outdated info from ladyada
http://www.ladyada.net/library/pcb/manufacturers.html
http://www.ladyada.net/library/pcb/manufacturers.html




Line 26: Line 25:
*heat transfer - using heat
*heat transfer - using heat
*permanent marker - yep sharpie will resist etching, too
*permanent marker - yep sharpie will resist etching, too
===Design===
*spacing: 10-12mil
*route: 5mil
*Adjust routing and/or footprints as necessary.


===Preparation===
===Preparation===
Line 62: Line 66:
**only use for thinner boards (0.032-)
**only use for thinner boards (0.032-)
**abuses blade
**abuses blade
#30 minutes prior to transfer, turn on laminator.
#*Use thickest setting for highest heat.


===Print===
===Print===
When printing your design, there are two critical things to keep in mind.
When printing your design, there are two critical things to keep in mind.
*Print a mirror image.
*Print a mirror image, scale to 1.
*Set printer to maximum density. Use Transparency setting, if available.
*Set printer to maximum density. Use Transparency setting, if available.


Line 72: Line 80:
#Mark top sheet in paper tray for side and orientation.
#Mark top sheet in paper tray for side and orientation.
#Print circuit.
#Print circuit.
#*top OR bottom layer, pads, vias
#*no docu/caption
#*Verify components fit on their footprints.
#*Verify all traces are clear and distinct.
#Cut transfer paper slightly larger than image.
#Cut transfer paper slightly larger than image.
#Tape transfer paper over image, shiny side exposed.
#Tape transfer paper over image, shiny side exposed.
Line 81: Line 93:


===Transfer===
===Transfer===
#Cut board to appropriate size
#*Leave enough board to push through laminator; At least two inches.
#Scour copper surface
#Scour copper surface
#*Use scouring pad and a dab of soap
#*Use scouring pad and a dab of soap
Line 90: Line 104:
#Carefully trim excess paper with a razor or sharp scissors.
#Carefully trim excess paper with a razor or sharp scissors.
#Maintaining alignment, apply heat with either laminator or iron.
#Maintaining alignment, apply heat with either laminator or iron.
#*Laminator - Depending on the power of your machine, run your board through 2-6 times.
#*Laminator - Depending on the power of your machine, run your board through 2-6 times changing direction at least once.
#*Iron - I have no experience with this method. The more heat and pressure, the better.
#*Iron - I have no experience with this method. The more heat and pressure, the better.
#Place board in water. Paper will release after a few seconds.
#Place board in water. Paper will release after a few seconds.
Line 98: Line 112:
#*If small amounts of toner are missing, use fine-point permanent marker to carefully draw them in.
#*If small amounts of toner are missing, use fine-point permanent marker to carefully draw them in.
#*If large amounts of toner are missing, wipe the toner off and restart.
#*If large amounts of toner are missing, wipe the toner off and restart.
#*Remove excess toner with a razor blade.


If not using sealing foil, proceed to Etch section.
If not using sealing foil, proceed to Etch section.
Line 104: Line 119:
#Allow board to dry. (Do NOT wipe dry!)
#Allow board to dry. (Do NOT wipe dry!)
#Cut piece of foil slightly narrower, and 1"-2" longer than board.
#Cut piece of foil slightly narrower, and 1"-2" longer than board.
#Place foil such that all the toner is covered, and a large flap is folded under the board. This will prevent slipping when applying heat.
#Place foil, dull side down, such that all the toner is covered, and a large flap is folded under the board. This will prevent slipping when applying heat.
#Being careful to avoid folds and wrinkles, run foil-wrapped board through laminator ONCE.
#Being careful to avoid folds and wrinkles, run foil-wrapped board through laminator twice.


Traces should now be covered in green. If there are still black portions, this should be fine. Toner is sufficient to mask; the sealant is merely added protection.
Traces should now be covered in green. If there are still black portions, this should be fine. Toner is sufficient to mask; the sealant is merely added protection.
Line 112: Line 127:
Some prefer using a sponge to apply the etchant. This is messy and slow, so we will use the submersion method. If you're interested in the sponge method, more information is at [http://www.instructables.com/id/Sponge-Ferric-Chloride-Method-Etch-Circuit-Bo/ Instructibles]
Some prefer using a sponge to apply the etchant. This is messy and slow, so we will use the submersion method. If you're interested in the sponge method, more information is at [http://www.instructables.com/id/Sponge-Ferric-Chloride-Method-Etch-Circuit-Bo/ Instructibles]


#Trim excess copper board to avoid wasting etchant.
#If only using one container, dump water out.
#If only using one container, dump water out.
#Fill container with enough etchant to cover board.
#Fill container with enough etchant to cover board.
Line 129: Line 145:
Congratulations! Your board is now ready for drilling, if necessary, and population.
Congratulations! Your board is now ready for drilling, if necessary, and population.


==The Homemade Process==
===Cleanup===
Design:
*Return used etchant to container for future reuse.
*Create your eagle design, use 10-12 mil spacing in your DRU, route to 5mil, you may also find you need to alter your footprints to get the spacing between, say, smd pins to somewhere the process can handle it
**DO NOT dump down train. Etchant is toxic and contains heavy metals. Check MSDS for disposal instructions.
 
*Dump water down drain while running cold water.
Setup:
*Thoroughly clean up any spilled etchant.
*30 minutes prior to wanting to create your board, turn on lamintor making sure 5mil switch is turned on for hotter operation
*Return printer to typical settings.
*set your printer to ink density 5, mark the page which will print so you know how to position
 
 
Print:
*print gtl layer (top or bottom, pads and vias), make sure you mirror and make the scale 1 with no caption
*check that all your individual components fit on their footprints properly and that all your traces and components are sufficiently distinct
*cut out blue transfer paper larger than printed design and scotch tape over top of printed design
*place back in printer properly so blue gets printed on(shiny side printed on)
*when it comes out, remove tape
 
Transfer:
*cut a peice of board with the paper cutter to the size of your design, but make sure board is long enough to be fed through laminator. (a couple inches long--you could attempt multiple designs at a time to fill the space or just trim this off later before etching)
*buff board a little bit with green scotch pad and a little detergent and clean and dry any residue
*ready some water deep enough to later submerse your completed copper with fused transfer paper
*put printed blue face down on copper and insert into laminator and when it comes out the other side, insert again same face up but from the other direction
*when it comes out immediately submerse in water and agitate until the blue paper falls off
*remove from water and carefully dry
*again check that your traces are distinct, you may want to carefully clean them up with a razor blade or add to them with a sharpie
 
Seal:
*cut a peice of green foil not quite as wide as your copper but several inches longer than your design
*place it dull side over the design overlapping the forward edge an inch or 2, and feed this edge to the laminator
*when it comes out again, feed the exact same way again
*when it comes out second time slowly remove green foil, wrinkles are what we were attempting to avoid, if you get wrinkles you may just try your etch anyway, but in future I find best way to remove wrinkles is to overlap more foil over the front so you can feed it tightly, and making sure foil does NOT overlap on the sides
*the green foil I find tends to blur traces together a bit more even, so I tend to use a razor blade to very carefully make all traces and pads distinct again if need be
 
Etch:
*you should now cut the copper down to the smallest size to speed up etching and avoid wasting etchant
*put not used up acid in a tub or cup deep enough to submerge design
*put gloves on as etchant stains permanently
*you may want to use electrical tape on the edge of your copper to give yourself something to hold on to when you submerge design
*you should then agitate the design in the etchant for several minutes
*the design will etch from the outside in so you can help the process along by lifting it out of the acid and gently rubbing your finger over the design, breaking hte surface tension and mixing up the etchant
*eventually all visible copper will be eaten away and all your traces and pads are distinct
*drop finished design back into water bath to nuetralize acid
 
Cleanup:
*return printer to ink density 3
*if etch went fine and acid still seems fresh, replace etchant back into a container for reuse, we need to find disposal method for non fresh acid, please dont dump down drain as it contains copper heavy metals and is toxic
*dump water and clean any spilled acid thoroughly

Revision as of 04:36, 5 February 2011

Professional Options

batchpcb for fairly quackish and cheap turnaround - 1 month seedstudio for opening your product up and/or cheap as low as 30 bucks for 5 boards

otherwise find a deal with the big boys advanced pcb (4pcb.com) has 2 layer 33 each at 33each.com (min 4+1free comes to like 150 shipped) a and they have a decent system for checking your design at freedfm.com

One problem you should already have noticed is these places have 100 domains so its hard to know if you're dealing with the same shop.

haven't tried them but http://www.goldphoenixpcb.biz http://www.expresspcb.com/ExpressPCBHtm/HowWorks.htm http://www.sunstone.com/QuoteQT.aspx (pcbexpress, pcb123) www.batesquote.com


some good but perhaps outdated info from ladyada http://www.ladyada.net/library/pcb/manufacturers.html


Homebrew

There are several options for home etching, but they all boil down to covering up the copper you DON'T want to take off, and bathing the rest in acid.

  • photo resist - using light to affix your pattern
  • heat transfer - using heat
  • permanent marker - yep sharpie will resist etching, too

Design

  • spacing: 10-12mil
  • route: 5mil
  • Adjust routing and/or footprints as necessary.

Preparation

You will need:

  1. 30 minutes prior to transfer, turn on laminator.
    • Use thickest setting for highest heat.


Print

When printing your design, there are two critical things to keep in mind.

  • Print a mirror image, scale to 1.
  • Set printer to maximum density. Use Transparency setting, if available.

These instructions assume you're using toner transfer paper.

  1. Mark top sheet in paper tray for side and orientation.
  2. Print circuit.
    • top OR bottom layer, pads, vias
    • no docu/caption
    • Verify components fit on their footprints.
    • Verify all traces are clear and distinct.
  3. Cut transfer paper slightly larger than image.
  4. Tape transfer paper over image, shiny side exposed.
    • Be sure not to cover important parts with tape!
    • Cover entire leading edge with tape to avoid jams.
  5. Place paper back in tray, noting orientation.
  6. Print image again with darkest setting.
  7. Remove transfer paper.

Transfer

  1. Cut board to appropriate size
    • Leave enough board to push through laminator; At least two inches.
  2. Scour copper surface
    • Use scouring pad and a dab of soap
    • Use very light pressure. You're trying to roughen the copper, not remove it.
    • Surface should be slightly dull, with no gouges.
  3. Rinse/dry board.
  4. Partially fill one container with clean, cool tap water.
  5. Align image on transfer paper with board.
  6. Carefully trim excess paper with a razor or sharp scissors.
  7. Maintaining alignment, apply heat with either laminator or iron.
    • Laminator - Depending on the power of your machine, run your board through 2-6 times changing direction at least once.
    • Iron - I have no experience with this method. The more heat and pressure, the better.
  8. Place board in water. Paper will release after a few seconds.
  9. Remove board from water, ensuring all paper has been removed.
    • Be careful not to remove toner.
  10. Inspect traces for excess/light toner.
    • If small amounts of toner are missing, use fine-point permanent marker to carefully draw them in.
    • If large amounts of toner are missing, wipe the toner off and restart.
    • Remove excess toner with a razor blade.

If not using sealing foil, proceed to Etch section.

If using sealing foil:

  1. Allow board to dry. (Do NOT wipe dry!)
  2. Cut piece of foil slightly narrower, and 1"-2" longer than board.
  3. Place foil, dull side down, such that all the toner is covered, and a large flap is folded under the board. This will prevent slipping when applying heat.
  4. Being careful to avoid folds and wrinkles, run foil-wrapped board through laminator twice.

Traces should now be covered in green. If there are still black portions, this should be fine. Toner is sufficient to mask; the sealant is merely added protection.

Etch

Some prefer using a sponge to apply the etchant. This is messy and slow, so we will use the submersion method. If you're interested in the sponge method, more information is at Instructibles

  1. Trim excess copper board to avoid wasting etchant.
  2. If only using one container, dump water out.
  3. Fill container with enough etchant to cover board.
  4. Place board in etchant bath.
    • Be careful to avoid splashing. This stuff stains, and is a skin/eye irritant. Reading the MSDS for unfamiliar chemicals is always a great idea.
  5. Agitate bath 5-10 minutes. (unless using bubble tank)
    • Shake container
    • Gently rub board with (gloved!) finger.
    • Check board frequently.
    • Most of the visible etching happens very quickly toward the end of the process.
  6. Submerge board in water or rinse in sink to remove all etchant.
  7. Pour used etchant back into bottle for reuse.
    • You can get several boards from a single batch of etchant.
    • Do not dispose of used etchant down drain.
  8. Dry board.

Congratulations! Your board is now ready for drilling, if necessary, and population.

Cleanup

  • Return used etchant to container for future reuse.
    • DO NOT dump down train. Etchant is toxic and contains heavy metals. Check MSDS for disposal instructions.
  • Dump water down drain while running cold water.
  • Thoroughly clean up any spilled etchant.
  • Return printer to typical settings.
Retrieved from "https://heatsynclabs.wiki:443/index.php?title=PCB_Etching&oldid=3628"